![]() If you’re working with a blank slate, try using painter’s tape to help you visualize the shelf placement! Mark studsįirst things first! See what kind of studs you’re working with! This is my favorite stud finder to use– it’s simple and reliable! Here’s a great resource to help determine spacing for shelves in a coat closet pantry! I also used our previous wire shelves to help get a better idea of spacing. Having an idea of what you’re going to store on the floating shelves will help you determine your dimensions and spacing.Īnother thing that helped was choosing our pantry baskets first so I could ensure the depth of my floating shelves would accommodate them! This will be your guide for drilling holes in the floating shelves.Step One: Planning & Preparation Planning your DIY floating shelvesīecause I was making DIY floating shelves for a pantry makeover, it was important to figure out the exact plan for that first! Below is the small pantry design I came up with! Mark on the scrap wood at the center of each hardware post. Finally, take a piece of scrap wood and lay it across your hardware. Use your laser level to mark a perfectly level line where you want your shelf to sit. We placed a piece of hardware on every stud available on our walls. This is where your floating shelf bracket will be installed. Using painter’s tape mark where your studs are. We wanted our shelves to be “thin” and not bulky so we decided to drill out the hole for the hardware.īefore deciding where to hang your shelves you need to find the studs in your wall. One way to achieve this look is to create a hollow pocket for the hardware to sit in. There are a couple of different ways to achieve this look. All the hardware is hidden inside the shelf. The smaller your shelves are the easier this will be but we have very long shelves and it was a bit more complicated to hang.įloating shelf brackets allow for a seamless modern floating shelf. This step takes some planning and lots of patience. Step Five: Installing Floating Shelves Brackets Finally, we finished with two coats of matte polyurethane to protect the finish. Next, we applied our stain liberally with a rag, wiping off the excess. This allowed us to get an even coat of stain and prevented any streaking. We selected ours based on what it looked like on Red Oak.īefore applying the stain we used a wood conditioner following the directions on the can. The same color stain will look different on each wood type. When choosing a stain be mindful of the type of wood you are staining. Simply White has a beautiful pickled white-washed look that gave us the light wood finish we were looking for. You can choose any stain color that you would like for this project. ![]() We wanted the desk and the floating shelves to be a perfect match. This stain color is the same that we used for our DIY desktop. Step Four: Stain DIY Thin Floating Shelvesįor the stain, we choose the stain Simply White by MinWax. Keep this in mind as you plan out the boards before cutting to length. Because the boards are glued together, if you have to cut one board to a specific length, you will be cutting two. Next, you will need to decide if you need to remove any length from the 8-foot pieces based on the length that you want your shelves to be. If you can, get a second set of hands to help with moving the boards around and cutting them. Safety Tip: Plywood boards are ¾ inch thick, 8 feet long, and made of oak, they are going to be heavy and awkward to handle. Alternatively, if you have a Table Saw, you can feed your board through that at 12 inches. When everything is in place carefully rip your boards in half. Mark 12 inches with a Chalk Line to ensure you are cutting your boards in a straight line. Taking your circular saw and Kreg Guide, set the guide to 12 inches. This means we cut the 4-foot boards into (4) 12-inch boards lengthwise and then glued them together. Our shelves are 12 inches deep and 1.5 inches thick. Once you have all your materials the first step is to cut your plywood to width and length. This allowed us to create (2) L-shaped shelves to mimic the shape of our desk. We used (2) 8-foot and (2) 4-foot 5-inch shelves. Since we used 4 x 8-foot plywood boards and needed 4 shelves we decided to do 12-inch deep shelves. The first thing you want to do for any project is plan out where you want your shelves and how long and deep they will be. “ Affiliate links provided for your convenience, please read my disclosure for more information.”Ĭhalk Line Step One: Measuring & Cutting the Plywood Adjust material quantity based on your project. They can also be used in any location you need the extra storage. DIY Thin Floating Shelves Materials List:Īlthough we did double L-shaped thin floating shelves above our desk you can use this tutorial for any length of shelves.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |